Mixxx 1.11.07/14/2023 ![]() > 0 goes one forward 0 indicates the index of the focused effect. Integer, read-only clear ¶ clear ¶ clear ¶īinary chain_selector ¶ ] chain_selector ¶ ] chain_selector ¶ The number of EffectUnits in this rack Range Loop range in waveform activates or deactivates and play position moves to loop in point.īinary num_effectunits ¶ num_effectunits ¶ num_effectunits ¶ Seeks forward (positive values) or backward (negative values) at a speed determined by the valueĭeck seeks rateEngine ¶ rateEngine ¶ rateEngine ¶Īctual rate (used in visuals, not for control) reloop_andstop ¶ reloop_andstop ¶ reloop_andstop ¶Īctivate current loop, jump to its loop in point, and stop playback. None, until you move the Speed slider rateSearch ¶ rateSearch ¶ rateSearch ¶ Sets the range of the Speed slider (0.08 = 8%) Temp up button & Speed slider rateRange ¶ rateRange ¶ rateRange ¶ Holds the speed one small step higher while active Range Temp up button & Speed slider rate_temp_up_small ¶ rate_temp_up_small ¶ rate_temp_up_small ¶ Holds the speed one step higher while active Range Temp down button & Speed slider rate_temp_up ¶ rate_temp_up ¶ rate_temp_up ¶ Holds the speed one small step lower while active Range Temp down button & Speed slider rate_temp_down_small ¶ rate_temp_down_small ¶ rate_temp_down_small ¶ Holds the speed one step lower while active Range Perm up button & Speed slider rate_temp_down ¶ rate_temp_down ¶ rate_temp_down ¶ Sets the speed one small step higher (1 % default) Range Perm up button & Speed slider rate_perm_up_small ¶ rate_perm_up_small ¶ rate_perm_up_small ¶ Sets the speed one step higher (4 % default) Range Perm down button & Speed slider rate_perm_up ¶ rate_perm_up ¶ rate_perm_up ¶ ![]() Sets the speed one small step lower (1 % default) Range Perm down button & Speed slider rate_perm_down_small ¶ rate_perm_down_small ¶ rate_perm_down_small ¶ Sets the speed one step lower (4 % default) lower Range 1 or 1 rate_perm_down ¶ rate_perm_down ¶ rate_perm_down ¶ Speed slider rate_dir ¶ rate_dir ¶ rate_dir ¶ Be sure to set back to 0 with scripts so the button does not stay lit. None eject ¶ eject ¶ eject ¶Įject button is lit. Outputs the length of the current song in seconds Range RangeĬue button duration ¶ duration ¶ duration ¶ If the player is not playing, set the cue point at the current location otherwise seek to the cue point. RangeĬue mark appears on the waveform cue_simple ¶ cue_simple ¶ cue_simple ¶ Sets a cue point at the current location. RangeĬue point marker cue_preview ¶ cue_preview ¶ cue_preview ¶Ĭue button lights and waveform moves cue_set ¶ cue_set ¶ cue_set ¶ The current position of the cue point in samples. ![]() These controls can be used in JavaScript files like this: Sets the value to -1.0 if the value was > -1.0, and to 1.0 if the value was -1.0, can tilt the crossfader from left to right Sets the value to 0.0 if the value was > 0.0, and to 1.0 if the value was 0.0, will cut off/on a track while you’re playing Sets the value to 0.0, put the crossfader in the middle again Output: set to 1.0 if the control is at its default, light up the pitch fader center indicator Input: sets the control to its default, return to default waveform zoom level Sets the value to -1.0, sets the channel volume to zero Sets the value to 1.0, sets the channel volume to full Increases the value by smaller step, sets the speed one small step higher (1 % default)ĭecreases the value by smaller step, sets the speed one small step lower (1 % default) ,rate_perm_up sets the speed one step higher (4 % default)ĭecreases the value, sets the speed one step lower (4 % default) The following extensions add some features to ControlPotMeter controls That it is either ‘ON’ (non-zero) or ‘OFF’ (zero). The default value range is 0.0 to 1.0, unless otherwise noted. You can read the ,play control to determine In Deck 1 can be accessed via the ,track_samplerateĬontrol. For example, the sample rate of the track loaded In addition to controlling Mixxx, the control system can be used to samplers, decks, and the preview deck all share Some groups have a high overlap ofĬontrols in common (e.g. The group is used to collect all the controls that affect one component Similarly, the volume fader for Sampler 1 is identified by the group Skins, MIDI controllers, HID controllers and keyboardsĪ control is identified by a “group” (which is used for groupingĪssociated controls) and a “key” (the name of the individual control).įor example, the volume fader for Deck 1 is identified by the group Nearly every knob, button, or fader you see in Mixxx’s interface isĬontrollable via Mixxx’s “control” system. Live Broadcasting - Start your own Internet radio
0 Comments
Leave a Reply. |